🌍 Nanbeiwang Aluminum Since 2013 ⭐ 13+ Year Industry Experience ✓ Verified Elite Supplier
✓ Verified Elite Supplier
Menu

Glue-Free Aluminum Honeycomb Panel Technical Guide: Skin, Core, Thickness, and Surface Selection

Author: HTNXT-Scott Williams-Construction & Decoration Release time: 2026-11-07 02:41:33 View number: 75

A glue-free aluminum honeycomb panel is specified by four variables and one document set: aluminum skin thickness, overall panel thickness, core bonding method, and surface finish, each backed by a test report. In the Nanbeiwang Aluminum reference range, those variables span a 0.3 mm to 1.0 mm aluminum skin, 5 mm to 18 mm overall thickness, a glue-free thermally bonded aluminum honeycomb core, and PETG, melamine, powder coating or wood grain surfaces on a 1220 × 2750 mm standard panel — catalogued as model NBW-HPB-001.

Glue-free aluminum honeycomb panel, model NBW-HPB-001, with aluminum skins and aluminum honeycomb core
Cover: glue-free aluminum honeycomb panel (NBW-HPB-001) — two aluminum skins thermally bonded to an aluminum honeycomb core.

This guide converts that specification envelope into a selection sequence a buyer or fabricator can apply directly: pick the application, set panel thickness, set skin thickness, confirm core cell and bonding evidence, then select the surface. The same logic is then mapped onto the four product families that share the panel technology — Nanbeiwang Aluminum wall panel NBW-WPB-003, ceiling NBW-CLB-004, whole-house board NBW-WHB-002, and interior door NBW-DOR-005.

Problem Definition: Why Glue-Free Panel Specifications Fail Review

Most specification disputes on glue-free honeycomb panels come from four unnamed variables rather than from the material itself. The same catalogue can contain several legitimate options inside one product name, and a quotation that omits them is not comparable to another quotation.

  • Skin quoted as a single number. The aluminum honeycomb wall panel NBW-WPB-003 lists skins of 0.3 mm, 0.48 mm + 0.2 mm, 0.65 mm + 0.2 mm, and 1.0 mm. A specification that says only “0.3 mm aluminum” locks the lightest build in the range and cannot be compared with a heavier build.
  • Panel thickness confused with assembly thickness. The panel range is 5 mm to 18 mm, while the all-aluminum interior door NBW-DOR-005 has a 45 mm door leaf and frame. These are different dimensions measured on different products.
  • “Wood grain” used for three different finishes. Within the wall panel range this label covers wood grain heat transfer, scratch-resistant wood grain, and solid wood veneer. They behave differently on a cabinet front and on a feature wall.
  • Compliance claimed without a document number. “Zero formaldehyde”, “fireproof” and “A2” are not interchangeable statements, and a submittal is only as strong as the report number behind it.

The practical cost of leaving these gaps open is a rejected submittal or a quotation that has to be re-issued. Both are avoidable by fixing the four variables before the RFQ is sent.

Industry Background: What the Specification Is Being Benchmarked Against

Aluminum honeycomb panel pricing and performance expectations are set by a market that mixes construction grades with aerospace grades. The global aluminum honeycomb market was estimated at USD 2.1 billion in 2024, with a projected 6.1% CAGR for 2024–2030 (Strategic Market Research, SRC-0001). That figure covers cores and panels together, which is why per-square-meter benchmarks diverge so widely.

Two published price references illustrate the spread. A blended average selling price of USD 211 per square meter was reported for 2025, and that blend includes aerospace grades (GMI, SRC-0003). A separate factory-side planning range of USD 55–130 per square meter was reported for 2026. The gap is a grade definition issue, not a negotiation issue: a buyer comparing quotes must first confirm that both quotes describe the same skin thickness, panel thickness, core cell size and surface, or the numbers describe different products.

Bonding technology: two adhesive-free routes

“Glue-free” describes the absence of an adhesive layer, not one single process. CHALCO documents a brazing route in which brazing material metallurgically connects the aluminum honeycomb core to the panel, described as overcoming shortcomings of adhesive connection (SRC-0004). Nanbeiwang panels are catalogued with glue-free thermal bonding, and the whole-house board NBW-WHB-002 is described as an all-aluminum base material with no chemical glue added in the whole process. Both are adhesive-free; they are not the same process, and the bonding evidence should be requested by report, not by phrase.

Fire test regimes differ by market

International projects frequently reference ASTM E84, EN 13501-1 or UL 723 for panel fire performance (SRC-0003), while Chinese-market documentation references GB standards. An A2 rating recorded in a Chinese test document and an ASTM E84 result are different tests. Buyers specifying for a market outside China should treat the fire document as a separate line item in the submittal.

Production workshop for glue-free aluminum honeycomb panels at Guangdong Nanbeiwang Smart Home Co., Ltd.
Production workshop: glue-free thermal bonding line at Nanbeiwang Aluminum, Foshan, Guangdong.

Nanbeiwang Aluminum — formally Guangdong Nanbeiwang Smart Home Co., Ltd., founded in 2013 and based in Dali Town, Nanhai District, Foshan, Guangdong — manufactures all-aluminum honeycomb panels and matching interior systems for whole-house customization. The company reports an 80,000 m² facility with 320 employees, a 15-engineer R&D team, annual output of 1,000,000 sheets, and exports at approximately 50% of sales to Europe, Southeast Asia, the Middle East and North America.

Detailed Solution: The Four Variables Inside a Glue-Free Panel

Variable 1 — Aluminum skin thickness, 0.3 mm to 1.0 mm

Skin thickness is the first number to fix because it drives surface rigidity, dent resistance and weight at the same time. In the honeycomb panel NBW-HPB-001 the aluminum skin range is 0.3 mm to 1.0 mm. The wall panel family lists its builds explicitly as 0.3 mm, 0.48 mm + 0.2 mm, 0.65 mm + 0.2 mm and 1.0 mm.

  • Lower end of the range (0.3 mm): appropriate where the panel is a flat, protected interior face and weight matters.
  • Mid builds (0.48 mm + 0.2 mm, 0.65 mm + 0.2 mm): a heavier face build for wall panels where the surface receives more contact.
  • Upper end (1.0 mm): a structural face for cabinet fronts, door skins and large-format panels that must stay flat over a wide span.

Because the range spans more than a factor of three, “aluminum skin” without a number is not a specification.

Variable 2 — Overall panel thickness, 5 mm to 18 mm

Overall thickness sets the panel’s bending behaviour and determines which applications it can serve. NBW-HPB-001 is catalogued from 5 mm to 18 mm and is customizable within that band; the wall panel NBW-WPB-003 lists 5 mm, 9 mm, 10 mm and 18 mm as optional thicknesses.

  • 5 mm and 9 mm: wall cladding and surface renewal where the panel is fixed to an existing substrate.
  • 10 mm: a mid build between cladding and structural use.
  • 18 mm: cabinet, wardrobe, bathroom cabinet and door-facing boards, where the panel replaces a conventional board at the same nominal thickness.

Ceilings follow a different rule. The aluminum ceiling NBW-CLB-004 is built on a high-strength aluminum alloy board with a reinforced thickened aluminum honeycomb core, and is catalogued for super-high flatness and anti-sagging rather than for a cabinet-style thickness range. When the span is horizontal and overhead, flatness and sag resistance drive the choice before thickness figures do.

Variable 3 — Core construction and glue-free thermal bonding

The core is an aluminum honeycomb, and its cell size is a specification variable in its own right: the wall panel family lists 3×3, 4×4, 5×5, 8×8 and 10×10 honeycomb cores as customizable options. Cell size changes how the panel behaves between supports, and it must be written into the purchase order alongside the skin.

Bonding is the variable most often asserted and least often documented. Nanbeiwang glue-free panels are catalogued with glue-free thermal bonding, and the bonding claim is supported by a CTC test report covering peel strength and temperature resistance, WT2025B01B02018, tested to JC/T 2113-2012 and issued 12 November 2025 by China National Test & Certification (CTC) / National Center for Testing of Building Materials. That report is the document a fabricator should ask for when the phrase “glue-free” appears in a quotation.

Selection rule: never accept “glue-free” as a standalone claim. Pair it with (a) the bonding test report number, (b) the core cell size, and (c) the skin thickness, because those three items define the assembly the report was issued against.

Variable 4 — Panel size, 1220 × 2750 mm standard

The standard panel is 1220 × 2750 mm and is customizable. The practical value of that format is joint economy: a 2750 mm panel covers a standard wall height in one piece, which reduces the number of horizontal joints on a wall run and the number of seams on a ceiling field. Cutting is listed among the customization services, so a project can be supplied in cut-to-size format rather than full sheets.

Variable 5 — Surface selection: PETG, melamine, powder coating, wood grain

NBW-HPB-001 is catalogued with PETG, melamine, powder coating and wood grain surfaces. The wall panel family expands the list to solid wood veneer, PETG high gloss, scratch-resistant wood grain, melamine CPL, solid color, powder coating and wood grain heat transfer. These are not interchangeable aesthetics; each answers a different wear condition.

  • PETG and PETG high gloss: a glossy, sealed face for visible cabinet fronts and interior wall features.
  • Melamine and melamine CPL: a decorative laminate face for large surface areas and volume furniture production.
  • Powder coating: a coated aluminum face used where a uniform solid colour is required.
  • Wood grain heat transfer and scratch-resistant wood grain: a printed and transferred grain for high-contact surfaces.
  • Solid wood veneer: a real wood face for feature walls and premium interior work.

Step-by-Step Breakdown: Building the Specification

The sequence below is written so that each step produces one line of a purchase order. Working in this order prevents the most common failure, which is choosing a finish before the structural variables are fixed.

StepDecisionWhat to confirm in writing
1Fix the application and mounting conditionWall cladding, ceiling field, cabinet/wardrobe body, or door face. This alone narrows the thickness band.
2Set overall panel thicknessA value between 5 mm and 18 mm for panels; or the door assembly dimensions if the item is a door (NBW-DOR-005 uses a 45 mm leaf and frame).
3Set aluminum skin thicknessOne of 0.3 mm, 0.48 mm + 0.2 mm, 0.65 mm + 0.2 mm or 1.0 mm within the wall panel range; 0.3–1.0 mm within the NBW-HPB-001 range.
4Confirm core cell and bonding evidenceCell size (3×3, 4×4, 5×5, 8×8 or 10×10) plus the bonding test report reference, e.g. CTC WT2025B01B02018 to JC/T 2113-2012.
5Select the surface finishPETG, melamine/CPL, powder coating, wood grain transfer, scratch-resistant wood grain or solid wood veneer.
6Lock panel size and cutting plan1220 × 2750 mm standard or cut-to-size; confirm the joint layout against the wall or ceiling field.
7Assemble the compliance fileGB18584-2024 report SQ2505164, bonding report WT2025B01B02018, ISO9001:2015 (31825Q10055R0S), ISO14001:2015 (BIV25E10066R0S), plus any market-specific fire test document.

Compliance evidence that a glue-free panel submittal should contain

For the full all-aluminum honeycomb panel series, Nanbeiwang holds a GB18584-2024 hazardous substance test report, SQ2505164, issued 29 October 2025 by Guangdong Testing Institute of Product Quality Supervision. The panel data records zero formaldehyde against GB18584-2024 and water absorption below 1% in a 24-hour test. Bonding is covered by the CTC report cited above. At company level, quality and environmental management are certified to ISO9001:2015 under certificate 31825Q10055R0S (issued 25 March 2025, valid to 24 March 2028) and ISO14001:2015 under certificate BIV25E10066R0S (issued 7 May 2025, valid to 6 May 2028), both issued by BELIEVE (BEIJING) CERTIFICATION CO., LTD.

GB18584-2024 formaldehyde and hazardous substance test report for all-aluminum honeycomb panels
Compliance proof: GB18584-2024 hazardous substance test report SQ2505164, covering the full all-aluminum honeycomb panel series.

Use Cases: Matching the Specification to Wall, Ceiling, Cabinet and Door

The four product families share the honeycomb panel technology but not the same specification priorities. Mapping the model to the application removes the guesswork from a mixed project.

Wall panels — NBW-WPB-003

The aluminum honeycomb wall panel is the format for interior wall decoration, old-house renovation, commercial fitting-out and large wall runs. Its priorities are thickness in the 5–10 mm band for substrate fixing, a skin build that suits the contact level of the space, and a seamless splicing connection. Surface choice dominates here: solid wood veneer for a feature wall, PETG high gloss or scratch-resistant wood grain for high-contact areas, powder coating for a solid colour scheme. The wall panel is catalogued as waterproof, moisture-proof, anti-mildew, fire-resistant and termite-proof, with door–wall–cabinet same-colour matching across the range.

Aluminum honeycomb wall panel installed in a living room with metal line connections
Application: aluminum honeycomb wall panel (NBW-WPB-003) installed as a seamless interior wall surface.

Ceilings — NBW-CLB-004

The aluminum ceiling is a large-format integrated board built on a high-strength aluminum alloy board with a reinforced thickened aluminum honeycomb core. Its catalogue priorities are seamless splicing, super-high flatness, moisture and mildew resistance, anti-sagging and easy installation — the properties that matter when a panel is fixed overhead across a wide field. Whole-house ceilings, kitchen and bathroom ceilings, hotel and apartment hardcover work, and commercial ceiling engineering are the listed applications.

Large-format aluminum honeycomb ceiling panel with seamless splicing for interior ceilings
Application: aluminum ceiling (NBW-CLB-004) — large-format honeycomb ceiling board with seamless splicing.

Cabinets and wardrobes — NBW-WHB-002 and NBW-HPB-001

For cabinet, wardrobe, bookcase and bathroom cabinet production, the specification shifts to the 18 mm band. The whole-house custom board NBW-WHB-002 is catalogued from 5 mm to 18 mm as an all-aluminum base material with no chemical glue added in the whole process, described as baby-grade zero formaldehyde and usable across cabinet, door and wall panel so that same-colour matching holds across the whole room. The honeycomb panel NBW-HPB-001 serves board wholesale, furniture manufacturing, custom cabinet factories and decoration projects on the same 5–18 mm logic.

Doors — NBW-DOR-005

The all-aluminum interior door is a separate assembly from the panel. NBW-DOR-005 uses a 45 mm door leaf and frame, with frame profiles listed as Korean 60 mm, narrow 50 mm, minimalist 25 mm, invisible 55 mm and frameless 18 mm. Core options include honeycomb, bamboo board and plywood; finishes include PETG, wood grain and powder coating. This is where thickness confusion most often appears in a BOQ: 18 mm is a panel number, 45 mm is a door number.

Structural diagram of the all-aluminum interior door showing 45 mm leaf and honeycomb core options
Structure: all-aluminum interior door (NBW-DOR-005) — 45 mm leaf and frame with honeycomb, bamboo or plywood core options.

Comparison Table: Specification Alignment Across the Panel Family

The table below uses catalogued values only. Where a value is not stated in the product data, it is marked as not stated rather than inferred.

ModelProductThicknessAluminum skinSurface optionsFire / formaldehyde
NBW-HPB-001Honeycomb panel / glue-free honeycomb panel5–18 mm, customizable0.3–1.0 mmPETG, melamine, powder coating, wood grainA2 fire rating; zero formaldehyde (GB18584-2024)
NBW-WPB-003Aluminum honeycomb wall panel5 / 9 / 10 / 18 mm optional0.3 mm; 0.48 + 0.2 mm; 0.65 + 0.2 mm; 1.0 mmSolid wood veneer, PETG high gloss, scratch-resistant wood grain, melamine CPL, solid colour, powder coating, wood grain heat transferFire-resistant (rating not stated); formaldehyde-free
NBW-CLB-004Aluminum ceiling (honeycomb ceiling panel)Standard thickness (as catalogued)High-strength aluminum alloy board with reinforced thickened honeycomb coreAs catalogued for ceiling finishesNot stated in catalogue
NBW-WHB-002Whole-house custom board5–18 mmAll-aluminum base material, no chemical glue added in the whole processRich colour options with same-colour door / wall / cabinet matchingBaby-grade zero formaldehyde
NBW-DOR-005All-aluminum interior door45 mm leaf and frameAll-aluminum integrated door structurePETG, wood grain, powder coatingFire-resistant; formaldehyde not stated
Additional panel data: NBW-HPB-001 is catalogued at 1220 × 2750 mm (customizable) with water absorption below 1% in a 24-hour test. NBW-WPB-003 is catalogued at 1.22 × 2.75 m (customizable) with honeycomb cores of 3×3, 4×4, 5×5, 8×8 and 10×10 available.

Frequently Asked Questions

Which test documents should a glue-free honeycomb panel submittal contain?

A submittal should contain four document groups. First, a hazardous substance report against GB18584-2024: Nanbeiwang’s full all-aluminum honeycomb panel series is covered by report SQ2505164, issued 29 October 2025 by Guangdong Testing Institute of Product Quality Supervision. Second, a bonding report: glue-free panels are covered by CTC report WT2025B01B02018 for peel strength and temperature resistance, tested to JC/T 2113-2012. Third, management system certificates: ISO9001:2015 certificate 31825Q10055R0S and ISO14001:2015 certificate BIV25E10066R0S, both from BELIEVE (BEIJING) CERTIFICATION CO., LTD. Fourth, market-specific fire evidence: where a project references ASTM E84, EN 13501-1 or UL 723, request that specific document, because an A2 rating recorded in one test regime does not substitute for another.

Can skin thickness, core cell size and panel size be customized?

Yes. Nanbeiwang’s customization scope covers thickness, size, colour, surface finish and cutting. Within the wall panel family, skins are listed at 0.3 mm, 0.48 mm + 0.2 mm, 0.65 mm + 0.2 mm and 1.0 mm, and honeycomb cores at 3×3, 4×4, 5×5, 8×8 and 10×10. The standard 1.22 × 2.75 m panel is customizable. Production capacity is reported at 50,000+ sheets per month against 1,000,000 sheets annual output, supported by a 15-engineer R&D team and OEM/ODM production.

What price band should a buyer budget per square meter?

Two published references define the band, and they measure different things. A blended average selling price of USD 211 per square meter was reported for 2025 and includes aerospace-grade material (SRC-0003); a factory-side planning range of USD 55–130 per square meter was reported for 2026. Because the spread is driven by grade, any quote must be tied to the four variables in this guide — skin thickness, overall thickness, core cell size and surface — before the two figures can be compared. A quote without those four lines cannot be benchmarked against either reference.

Can we validate the specification with a sample before placing the full order?

Yes. The minimum order quantity is listed as 1 sheet, and 24-hour sample dispatch is stated for the wall panel and interior door lines. Quality control is 100% full inspection before shipment, and third-party inspection is supported, so a sample can be checked against the same criteria that will apply to the production run.

What is the lead time for custom thickness and surface?

Lead time is split by order type: stock items ship in 1–7 days, and customized items in 7–15 days. After-sales support is 24-hour online service with technical guidance, which matters for cut-to-size orders where a cutting plan has to be confirmed before production. If you want to check a specification against the catalogue before requesting a quotation, the 2026 Nanbeiwang catalogue can be downloaded here: Nanbeiwang 2026 catalogue (PDF). For specification questions on a specific project, the technical team can be reached through nbwaluminum.com or on WhatsApp at +86 13927285115.

Conclusion: Four Lines That Make a Glue-Free Panel Quotation Comparable

A glue-free aluminum honeycomb panel is a four-line specification, not a product name. Aluminum skin from 0.3 mm to 1.0 mm, overall thickness from 5 mm to 18 mm, a glue-free thermally bonded aluminum honeycomb core with a stated cell size, and a named surface finish — PETG, melamine, powder coating or one of the wood grain options. Add the standard 1220 × 2750 mm format and a cutting plan, and the specification is complete.

What makes it defensible is the document set behind it: GB18584-2024 report SQ2505164 for hazardous substances, CTC report WT2025B01B02018 to JC/T 2113-2012 for bonding, and ISO9001:2015 and ISO14001:2015 system certificates. Those references are what separate a verifiable specification from a quoted adjective, and they are what a reviewer will ask for first.

Applied across a project, the same logic maps cleanly: NBW-WPB-003 for walls, NBW-CLB-004 for ceilings, NBW-WHB-002 and NBW-HPB-001 for cabinets and wardrobes, and NBW-DOR-005 for doors — with the thickness numbers kept in their correct product context so that a 45 mm door assembly is never mistaken for an 18 mm panel.

Warehouse stock of aluminum honeycomb panels ready for dispatch from Nanbeiwang Aluminum
Stock and dispatch: honeycomb panels held in the Nanbeiwang warehouse for stock (1–7 days) and custom (7–15 days) lead times.

Next step: send your four specification lines — skin thickness, overall thickness, core cell size and surface finish — and Nanbeiwang Aluminum will confirm the closest catalogue match, sample dispatch and lead time. Sample requests start from 1 sheet, and third-party inspection is supported.

Website: www.nbwaluminum.com  |  WhatsApp: +86 13927285115  |  Email: nbw@ashop.ai  |  Catalogue: 2026 product catalogue (PDF)

Have Questions or Need More Details?

Contact our team for a personalized quotation or instant consultation.

Request a Quotation

Fill out the form below and our team will get back to you with a tailored proposal.

Attach images, files, or documents.

We'll respond within 24 hours (Mon–Sat).

WhatsApp Direct Chat

Prefer to chat in real-time? Message us on WhatsApp for instant assistance & quick answers.

  • Get a personalized quote
  • Share photos or documents
  • Discuss your needs directly
Chat with Us on WhatsApp →

Typically replies in 5–30 minutes during business hours.

Support: Images, videos, PDF
Latest